What the Seachem Ammonia Alert Actually Does
The Seachem Ammonia Alert is a small, self-contained device that continuously detects toxic free ammonia in your aquarium water. Unlike liquid test kits that require you to take a sample and add reagents, this monitor sits inside the tank and changes color based on the ammonia concentration. It works in both freshwater and marine setups, and it detects free ammonia levels as low as 0.05 mg/L (ppm). The sensor lasts over a year, which is much longer than competing products that typically last only 4 to 6 weeks.
Key Facts About the Ammonia Alert
- Seachem Ammonia Alert: The sensor changes reversibly from yellow to green to blue, relative to the ammonia concentration. You don't need to interpret numbers—just match the color to the guide to know if ammonia is at SAFE, ALERT, ALARM, or TOXIC levels.

Seachem Ammonia Alert - Seachem Ammonia Alert: Response time to rising ammonia is about 15 minutes; response to decreasing ammonia takes about 4 hours. This means the device gives you a quick warning when ammonia spikes, but it's not a tool for immediate re-testing after a water change.
- Seachem Ammonia Alert: The device detects less than 0.05 mg/L free ammonia and alerts you to the #1 killer before any sign of stress. You can catch dangerous ammonia levels before your fish or shrimp show visible symptoms, giving you time to act.
How to Set Up the Ammonia Alert
Setting up the Seachem Ammonia Alert is straightforward. Remove the device from its packaging—it may have a greenish hue when dry, which is normal. Place it inside your aquarium, either floating or attached to the glass using the included suction cup. It should be positioned where water can flow freely over the sensor surface, but not directly in the path of strong filter output that could cause bubbles. Avoid placing it near air stones or where it might be splashed by surface agitation, as this can affect readings.
It may take a few days for a dry sensor to fully equilibrate with the water. During this time, the color may shift gradually as the sensor adjusts. Once equilibrated, the device will give reliable continuous readings. No chemicals, test kits, or water sampling are needed—just stick it in and let it work.
Step-by-Step Setup
- 1. Prepare the device: Remove the Ammonia Alert from the packaging. It may have a greenish tint when dry—this is normal and will change once submerged.
- 2. Place in the aquarium: Attach the device to the glass using the suction cup, or let it float. Choose a spot with gentle water flow, away from strong currents and air stones.
- 3. Allow equilibration: Wait a few days for the sensor to stabilize. During this time, the color may shift as it adjusts to your water chemistry.
- 4. Read the color: After equilibration, check the sensor color under natural daylight or a daylight-simulating light. Avoid red-enhancing lights, as they can mask green and blue hues.
How to Read the Ammonia Alert Colors
The Ammonia Alert uses a simple color scale. In the absence of free ammonia, the sensor appears yellow or faint yellow-green. As free ammonia increases, the color shifts to green, then to blue. The supplied interpretation guide correlates these colors to specific free ammonia concentrations:
SAFE: Yellow or faint yellow-green (less than 0.02 mg/L free ammonia).
ALERT: Green (about 0.05 mg/L). This level is tolerated for several days.
ALARM: Deeper green-blue (about 0.2 mg/L). This level is tolerated for a few days.
TOXIC: Blue (about 0.5 mg/L). This level is rapidly harmful.
Note that as little as 0.02 mg/L free ammonia will produce a greenish hue. In marine water at pH 8.3, this corresponds to about 0.25 mg/L total ammonia; in freshwater at pH 7.0, it corresponds to about 3.6 mg/L total ammonia. Free ammonia is much more toxic than ionized ammonia, so the device focuses on the form that matters most.
Placement Tips for Best Results
For maximum sensitivity, read the device under natural daylight or a daylight-simulating light. Red-enhancing aquarium lights can minimize green and blue hues, making the sensor appear less sensitive than it actually is. If you use such lights, check the device briefly with a white light or natural light to get an accurate reading.
Keep the sensor free of algae. If algae grows on the surface, gently clean it with a soft, clean material—never use bleach, soap, detergents, or hard objects. Avoid touching the sensor with your fingers, as skin oils can damage it. The device is not recommended for use at acid pH, as the chemistry of free ammonia detection is less reliable under those conditions.
What the Ammonia Alert Won't Tell You
While the Ammonia Alert is excellent for continuous monitoring, it has limitations. It does not measure total ammonia (the sum of free and ionized forms), so you cannot directly compare its reading to a standard liquid test kit without accounting for pH and temperature. The response to decreasing ammonia is slow—about 4 hours to go from TOXIC to SAFE after removal of the ammonia source. This means it's not suitable for real-time tracking of a water change's effectiveness. Additionally, some dye medications may discolour the sensor, temporarily affecting readings. If you use such medications, consider temporarily removing the device or relying on a liquid test kit for the duration of treatment.
Care and Longevity
The Ammonia Alert requires no regular maintenance beyond keeping the sensor surface clean. Algae growth can be removed with a soft, clean material—avoid abrasive scrubbing. The sensor lasts over a year, which is more than nine times longer than competing products that typically last 4 to 6 weeks. Sensitivity actually improves with age, provided the unit is not allowed to dry out. However, if it does dry out, this does not permanently impair the unit—it will recover once re-submerged. If you need to check the device's response, hold it briefly over the mouth of an ammonia bottle (not over the tank) and observe the color change.


